Eletechsup News
NT18B07 FAQ
I bought it together with the NT18B07 ，The information is stored in the device for some time or only read instantly from the sensors Answer : only read instantly from the sensors
NT18B07 FAQ
I bought it together with the NT18B07 ，The information is stored in the device for some time or only read instantly from the sensors Answer : only read instantly from the sensors
ET69C02 FAQ
ET69C02 ， Hi, we have a lot of your network modules connected to your relay modules. we have encountered an issue. The network modules loose their connection to the network. They start working fine after setup but in time just loose connection and there is not ping to them and no web interface, until you restart the network module, and sometimes even have to reset the module. We have tried to increase the voltage to 12.9-13.0 volts, but it did not work. This is our general configuration: Answer : 1 The power supply may be disturbed. Please use an independent DC 12V power supply 2 The network interface may be disturbed. Please change the network cable environment 3 If the problem still cannot be solved, please replace the ET69C02 board.
ET69C02 FAQ
ET69C02 ， Hi, we have a lot of your network modules connected to your relay modules. we have encountered an issue. The network modules loose their connection to the network. They start working fine after setup but in time just loose connection and there is not ping to them and no web interface, until you restart the network module, and sometimes even have to reset the module. We have tried to increase the voltage to 12.9-13.0 volts, but it did not work. This is our general configuration: Answer : 1 The power supply may be disturbed. Please use an independent DC 12V power supply 2 The network interface may be disturbed. Please change the network cable environment 3 If the problem still cannot be solved, please replace the ET69C02 board.
KC23C01 FAQ
Hello, I have your " KC23C01 " I do not have the user manual. I need to open an electric lock (for 2 seconds) after pressing the button X times. I would like to know if the electrical connection is correct and how to program the board so that it does this job. Thanks Answer : Question : Ok I did as your drawing. Now I have to set it so that after I press the button 5 times the contact closes for 3 seconds and then goes back to rest. I have to make 10 pieces, tell me how to make the first one and then I'll make the others thanks thanks Answer : https://youtu.be/wOeR_py7Jfo
KC23C01 FAQ
Hello, I have your " KC23C01 " I do not have the user manual. I need to open an electric lock (for 2 seconds) after pressing the button X times. I would like to know if the electrical connection is correct and how to program the board so that it does this job. Thanks Answer : Question : Ok I did as your drawing. Now I have to set it so that after I press the button 5 times the contact closes for 3 seconds and then goes back to rest. I have to make 10 pieces, tell me how to make the first one and then I'll make the others thanks thanks Answer : https://youtu.be/wOeR_py7Jfo
R4D3C32 FAQ
Can you email me the RTU addresses this board uses? It is not in the files I downloaded Answer: The address of R4D3C32 is set by the DIP switch. Please check the status of the DIP switch on the board. Generally, it is 1. ...
R4D3C32 FAQ
Can you email me the RTU addresses this board uses? It is not in the files I downloaded Answer: The address of R4D3C32 is set by the DIP switch. Please check the status of the DIP switch on the board. Generally, it is 1. ...
NT48A08 FAQ
Question： And You published on YT video with NT48A08. Link to Aliexpress no works. On your www there is no suche board. Please reply. Can this module mesure 0-190 ohm...
NT48A08 FAQ
Question： And You published on YT video with NT48A08. Link to Aliexpress no works. On your www there is no suche board. Please reply. Can this module mesure 0-190 ohm...
N4D3E16 Copied board from Original Eletechsup b...
Question : I want to buy this circuit in new, but this one don`t Work and had only 8ch from 16ch with delay function. Have original circuits a 16ch delay...
N4D3E16 Copied board from Original Eletechsup b...
Question : I want to buy this circuit in new, but this one don`t Work and had only 8ch from 16ch with delay function. Have original circuits a 16ch delay...